ICT XBA and XBA mini DIP Switch Settings (USD)
DIP switch settings for the ICT XBA and XBA mini bill acceptors configured for US dollars.
How to read these tables. ★ marks the manufacturer setting. A dash means that switch is not used by that setting — leave it where it is. A unit shipped from the factory has all switches OFF.
Power-cycle the acceptor after changing any switch. Settings are only read at startup.
XBA — USD6
Main DIP switch settings — left switch block (SW1–SW8)
↔ Swipe the table sideways to see every switch column.
| Function / Setting | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Reject $ 1 | ON | – | – | – | – | – | – | – |
| ★ Accept $ 1 | OFF | – | – | – | – | – | – | – |
| Reject $ 5 | – | ON | – | – | – | – | – | – |
| ★ Accept $ 5 | – | OFF | – | – | – | – | – | – |
| Reject $ 10 | – | – | ON | – | – | – | – | – |
| ★ Accept $ 10 | – | – | OFF | – | – | – | – | – |
| Reject $ 20 | – | – | – | ON | – | – | – | – |
| ★ Accept $ 20 | – | – | – | OFF | – | – | – | – |
| Reject $ 50 & 100 | – | – | – | – | ON | – | – | – |
| ★ Accept $ 50 & 100 | – | – | – | – | OFF | – | – | – |
| Disable Bill Reject 4 Times BA Stop By 30 Sec | – | – | – | – | – | ON | – | – |
| ★ Enable Bill Reject 4 Times BA Stop By 30 Sec | – | – | – | – | – | OFF | – | – |
| Stack Banknote when Power-up | – | – | – | – | – | – | ON | – |
| ★ Reject Banknote when Power-up | – | – | – | – | – | – | OFF | – |
| Reserved | – | – | – | – | – | – | – | ON |
| ★ Reserved | – | – | – | – | – | – | – | OFF |
Main DIP switch settings — right switch block (SW1–SW8)
↔ Swipe the table sideways to see every switch column.
| Function / Setting | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| ★ Inhibit Active HIGH | ON | – | – | – | – | – | – | – |
| Inhibit Active LOW | OFF | – | – | – | – | – | – | – |
| Reserved | – | ON | – | – | – | – | – | – |
| ★ Reserved | – | OFF | – | – | – | – | – | – |
| Reserved | – | – | ON | – | – | – | – | – |
| ★ Reserved | – | – | OFF | – | – | – | – | – |
| Reserved | – | – | – | ON | – | – | – | – |
| ★ Reserved | – | – | – | OFF | – | – | – | – |
| ★ Credit-Pulse Normal HIGH | SCALING_FACTOR 100 DECIMAL_PLACE_OFF 2 | Connect with coin change | – | – | – | – | ON | – | – | – |
| Credit-Pulse Normal LOW | SCALING_FACTOR 1 DECIMAL_PLACE_OFF 0 | Connect with ICT JPSTD Converter board | – | – | – | – | OFF | – | – | – |
| ★ Pulse Mode | – | – | – | – | – | ON | – | – |
| Other Mode | – | – | – | – | – | OFF | – | – |
| ★ 1 pulse / USD 1 | MDB Mode | – | – | – | – | – | – | OFF | OFF |
| 2 pulse / USD 1 | ICT002U Mode | – | – | – | – | – | – | OFF | ON |
| 4 pulse / USD 1 | ICT104U Mode | – | – | – | – | – | – | ON | OFF |
| 20 pulse / USD 1 | ICT104V Mode | – | – | – | – | – | – | ON | ON |
Currency assign data (bill value channels)
| Bill value | ICT002U | ICT104U | ICT104V | Pulse | MDB |
|---|---|---|---|---|---|
| BV1 | USD 1 | USD 1 | USD 1 | USD 1 | USD 1 |
| BV2 | USD 5 | USD 5 | USD 5 | USD 5 | – |
| BV3 | USD 10 | USD 10 | USD 10 | USD 10 | USD 5 |
| BV4 | USD 20 | USD 20 | USD 20 | USD 20 | USD 10 |
| BV5 | USD 50 | USD 50 | USD 50 | USD 50 | USD 20 |
| BV6 | USD 100 | USD 100 | USD 100 | USD 100 | USD 50 |
| BV7 | – | – | – | – | USD 100 |
Notes printed on the manufacturer sheet
- ★ Manufacture setting
- Note : 1. After setting dip switch of the credit pulses, you should reset the bill acceptor again.
- 2. Calibration card is needed.
- This dip switch is located at the side of XBA.
- This dip switch is located on the CPU board, remove the CPU board cover first.
XBA mini — USD6
Main DIP switch settings (8-switch DIP + 4-switch DIP)
↔ Swipe the table sideways to see every switch column.
| Function / Setting | 8-switch DIP | 4-switch DIP | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 | SW1 | SW2 | SW3 | SW4 | |
| Reject USD 1 | ON | – | – | – | – | – | – | – | – | – | – | – |
| ★ Accept USD 1 | OFF | – | – | – | – | – | – | – | – | – | – | – |
| Reject USD 5 | – | ON | – | – | – | – | – | – | – | – | – | – |
| ★ Accept USD 5 | – | OFF | – | – | – | – | – | – | – | – | – | – |
| Reject USD 10 | – | – | ON | – | – | – | – | – | – | – | – | – |
| ★ Accept USD 10 | – | – | OFF | – | – | – | – | – | – | – | – | – |
| Reject USD 20 | – | – | – | ON | – | – | – | – | – | – | – | – |
| ★ Accept USD 20 | – | – | – | OFF | – | – | – | – | – | – | – | – |
| Reject USD 50 & 100 | – | – | – | – | ON | – | – | – | – | – | – | – |
| ★ Accept USD 50 & 100 | – | – | – | – | OFF | – | – | – | – | – | – | – |
| Disable Bill Reject 4 Times BA Stop By 30 Sec | – | – | – | – | – | ON | – | – | – | – | – | – |
| ★ Enable Bill Reject 4 Times BA Stop By 30 Sec | – | – | – | – | – | OFF | – | – | – | – | – | – |
| Colorful light | – | – | – | – | – | – | OFF | OFF | – | – | – | – |
| ★ The green light flashes | – | – | – | – | – | – | OFF | ON | – | – | – | – |
| Reserved | – | – | – | – | – | – | ON | OFF | – | – | – | – |
| No light | – | – | – | – | – | – | ON | ON | – | – | – | – |
| Inhibit Active High | – | – | – | – | – | – | – | – | ON | – | – | – |
| ★ Inhibit Active Low | – | – | – | – | – | – | – | – | OFF | – | – | – |
| Reserved | – | – | – | – | – | – | – | – | – | ON | – | – |
| ★ Reserved | – | – | – | – | – | – | – | – | – | OFF | – | – |
| ★ Interface Timing Conversion: 5ms LO / 5ms HI | – | – | – | – | – | – | – | – | – | – | OFF | OFF |
| Interface Timing Conversion: 5ms LO / 10ms HI | – | – | – | – | – | – | – | – | – | – | ON | OFF |
| Interface Timing Conversion: 10ms LO / 10ms HI | – | – | – | – | – | – | – | – | – | – | OFF | ON |
| Interface Timing Conversion: 20ms LO / 20ms HI | – | – | – | – | – | – | – | – | – | – | ON | ON |
Interface settings — Pulse
↔ Swipe the table sideways to see every switch column.
| Function / Setting | SW1 | SW2 | SW3 | SW4 |
|---|---|---|---|---|
| ★ Credit-Pulse Normal HIGH | ON | – | – | – |
| Credit-Pulse Normal LOW | OFF | – | – | – |
| ★ Pulse Mode | – | ON | – | – |
| Other Mode | – | OFF | – | – |
| ★ 1 pulse / USD 1 | – | – | OFF | OFF |
| 2 pulses / USD 1 | – | – | OFF | ON |
| 4 pulses / USD 1 | – | – | ON | OFF |
| 20 pulses / USD 1 | – | – | ON | ON |
Interface settings — ICT104U
↔ Swipe the table sideways to see every switch column.
| Function / Setting | SW1 | SW2 | SW3 | SW4 |
|---|---|---|---|---|
| ★ Reserved | ON | – | – | – |
| Reserved | OFF | – | – | – |
| Pulse Mode | – | ON | – | – |
| ★ Other Mode | – | OFF | – | – |
| MDB Mode | – | – | OFF | OFF |
| JPSTD Mode | – | – | OFF | ON |
| ★ ICT104U Mode | – | – | ON | OFF |
| ICT104V Mode | – | – | ON | ON |
Interface settings — ICT104V
↔ Swipe the table sideways to see every switch column.
| Function / Setting | SW1 | SW2 | SW3 | SW4 |
|---|---|---|---|---|
| ★ Connect with coin changer | ON | – | – | – |
| Connect with ICT JPSTD Converter board | OFF | – | – | – |
| Pulse Mode | – | ON | – | – |
| ★ Other Mode | – | OFF | – | – |
| MDB Mode | – | – | OFF | OFF |
| JPSTD Mode | – | – | OFF | ON |
| ICT104U Mode | – | – | ON | OFF |
| ★ ICT104V Mode | – | – | ON | ON |
Interface settings — MDB
↔ Swipe the table sideways to see every switch column.
| Function / Setting | SW1 | SW2 | SW3 | SW4 |
|---|---|---|---|---|
| ★ Scaling Factor (SF) = 100 Decimal Point Position (DPP) = 2 | ON | – | – | – |
| Scaling Factor (SF) = 1 Decimal Point Position (DPP) = 0 | OFF | – | – | – |
| Pulse Mode | – | ON | – | – |
| ★ Other Mode | – | OFF | – | – |
| ★ MDB Mode | – | – | OFF | OFF |
| JPSTD Mode | – | – | OFF | ON |
| ICT104U Mode | – | – | ON | OFF |
| ICT104V Mode | – | – | ON | ON |
Currency assign data (bill value channels)
| Bill value | ICT104U | ICT104V | JPSTD | Pulse | MDB |
|---|---|---|---|---|---|
| BV1 | 1 | 1 | 1 | 1 | 1 |
| BV2 | 5 | 5 | – | 5 | – |
| BV3 | 10 | 10 | – | 10 | 5 |
| BV4 | 20 | 20 | – | 20 | 10 |
| BV5 | 50 | 50 | – | 50 | 20 |
| BV6 | 100 | 100 | – | 100 | 50 |
| BV7 | – | – | – | – | 100 |
Notes printed on the manufacturer sheet
- ★ Manufacture setting
- Note : (1) After setting dip switch of the credit pulses, you should reset the bill acceptor again.
- (2) Calibration card is needed.
Not sure which unit you have?
Denomination sets and interfaces vary by configuration part number, printed on the label on the side of the acceptor. Send us a photo of that label and we will confirm the exact model, firmware and correct switch settings — contact BillAcceptors.us.